Influential factors on bading resistance of C.5420 steel during carburizing
B. Radulovic, R. Adzic, V. Asanovic

Development of a high strength and medium electrical conductivity Cu-Ni-Ti Alloy
M. Backovic, M. Jovanovic

The mechanical properties and structure of forgings from high strength Al-Zn-Mg-Cu Alloys
M. Misovic, M. Vratnica, J. Curovic, Z. Burzic, G. Dapcevic

True Stress-Strain Curves in Elevated Temperature Tension test of AiMg6.8 Ally sheet
M. Dudukovaska, I. Ðokic, D. Glisic, E. Romhanji

Nickel Activity Determination in the System Ni-Cr-Co-Mo
D. Zivkovic, Z. Zivkovic, V. Trujic, A. Milosavljevic

Archaeomatallurgical Investigation of Findings from Kolut - Bacan Site
D. Zivkovic, V. Trujic, S. Janjic, M. Gavrilovski, V. Rajkovic, R. Curcic, D. Krajinovic

Possibility of Application of Cordierite in Foundry
Z. Acimovic, Lj. Pavlovic, S. Tripkovic

Influence of Rotationg Disk Formation Conditions on Al2O3 Ceramic Fiber Diameter
R. Jancic, R. Aleksic

Thermal Stability of (Al2O3+TiO2) Based Refractories: Resistance Parameters and Water Quench Test
T. D. Volkov-Husovic, R. M. Jancic, Z. V. Popovic

The effect of Heat Treatment on Mechanical and Structural Characteristics of a Special Aluminium Bronze
A. Kostov, R. Todorovic, G. Ðurasevic, M. Arsenovic

Correlation of Sintering Conditions Microstructure and Magnetic Properties of Sintering SmCo 5 Magnets
N. M. Talijan, V. Menushnikov, A. Mulitinovic-Nikolic, Z. Jovanovic

The effect of Heat Treatment and Rheocasting Process on Microstructure and Tensile Properties of ZA27 Alloy
I. Bobic, M. Jovanovic, N. Ilic

Deformation Affected Thermoelectric and Texture Properties of Fe and CuNi44 Wires
T. Pavlovic, Lj. Stojanovic, D. Markovic, B. Stanojevic

Autogenous Smelting Processes of Copper Concentrates
D. Vucurovic, C. Knezevic, Lj. Misic, M. Cirkovic, J. Marinkovic

Sixty years of Metallurgy of Lead "Trepca" in Zvecan
B. Nikolic

Synthesis of Nickel-Aluminide and Titan-aluminide Powders by Chemical Vapor Deposition
S. Stopic, M. Ristanovic, K. Raic

The Heat Regenerators Estimation in Program Application of heat Utilization Wasted Gases in new "Trepca" Lead Refinery
M. Barac, Z. Popovic

Metal Matrix Composites
D. Bozic, Z. Gnjidic, S. Riznic , M. Mitkov

A Microstructural Investigation of a Dental Amalgam
Z. Miskovic, B. Lukic, S. Zec, N. Ilic

The Influence of Solidification Rate on the Microstructure and Distribution of Solute During Solidification of Al-Cu Alloy
V. Radojevic, A. Valcic, A. Milutinovic- Nikolic

Homogeniety of Heavy Forgings
B. Sladojevic

Determination of the Thermodynamic Model for the System Bi-Ga 0.1 Sb 0.9
D. Zivkovic, Z. Zivkovic

Thermodynamic Analysis of Ternary System Pb-Sn-Ti
B. Vucinic, V. Fajnisevic, D. Zivkovic, Z. Zivkovic

Mechanism and Kinetics of Oxidation of Copper Sulfide Concentrate in Fluidized Bed Reactor - Part I
M. Cirkovic, J. Marinkovic, D. Vucurevic, S. Stopic

Properties of the Mixture with Coated and in Dependence of characterization of Quarz Sand
M. Krgovic, M. Lalovic, N. Blagojevic

Natural Iterative Learning Control of a Metallurgical Plant with Unknown Time- Delay
M. Lazarevic, D. Krstic

Survey of Qualitative Indicators for the Comparative Analysis of Bearing Alloys Tribological Properties
N. Fridrih, M. Babic, Z. Andic

Thermodynamics Investigations of the Ternary System Ga-Al-Sn Using the General Solution Model
D. Zivkovic, Z. Zivkovic, S. Zdravkovic , L. Gomidzelovic, M. Janosevic

Zone Model of Blast Furnace Process
R. Todorovic

A Contribution to the Study of Heat and Mechanical Effects on Metal - Mould Boundary Surface
Z. Janjusevic, Z. Gulisija

STM Image Visualization of Film Surface (Graphic Simulation and Implementation)
R. M. Sasic, K. T. Raic, T. Petrovic, M. Petkovska

Visualization of Thermal Shock Behavior of 42% (Al2O3 +TiO2) Based Refractory Samples
T. Volkov-Husovic, M. Cvetkovic, D. Mitrakovic, Z. Popovic

On the Importance of Metallurgical Knowledges in Studying the Roman Monetary Policy
B. Drca